Lock with Cylinder: How the Case, the Cylinder and the Door Preparation Have to Match

Studio flat lay on charcoal stone of a mortise lock case, a stainless forend plate, a separate satin nickel Euro profile cylinder, a stainless strike plate and two keys

A lock with cylinder is a lock case with no key mechanism of its own. The case carries the spring latch, the deadbolt, a bore for a Euro profile cylinder and a follower for the lever spindle. The cylinder is not in the box: it is bought separately, matched to the case, and the pair is then matched to the door.

Assume a cylinder comes with the case and you have a door that latches but cannot be locked. Buy a cylinder that does not suit the case and you have a part that will not seat, will not drive the bolt, or will not take its screw. Both mistakes surface after the door edge is cut.

Four interfaces decide whether the assembly works: the centers and backset that position both parts in the door, the bore and cam that join them, the follower that carries the spindle to the lever, and the forend and strike that close the door on the frame.

Finished oak door edge with a brushed stainless forend carrying a beveled latch and a square deadbolt, a lever handle above a satin nickel Euro profile cylinder set in the door face

What is actually in the box

ComponentComes with the caseWhat you still specify
Case, latch, deadbolt, forendYes, one article numberBackset, forend type and width, follower size, finish
Striking plate and screwsYesIts fixing has to suit the frame material
Euro profile cylinderNoLength for each side, key or thumb turn, security level
KeysWith the cylinderDiffers, keyed-alike groups, master-key structure
Spindle and lever furnitureNo8 or 9 mm spindle, length, sprung or unsprung lever
Intumescent protectionNoWhatever the tested door assembly calls for

The four interfaces that decide the job

Every failure in this category sits on one of four joints.

InterfaceWhat it fixesWhen it is wrongCheck before ordering
Centers and backsetWhere the lever axis and cylinder axis sit: 85 mm apart, 40–80 mm from the edgeCase will not enter the pocket, or the holes miss the lever and cylinderMeasure the door, not the old lock
Bore and camWhether a cylinder can pass through the case and turn the deadboltCylinder will not seat, cam misses its slot, screw will not line upCase drawing: bore, cam slot, screw position
Follower and spindleHow the lever drives the latchLever sags, lifts before the latch moves, or spinsFollower size, and the spindle in the furniture
Forend and strikeWhether the door closes cleanly and both bolts engagePlate stands off or overhangs, latch rubs, door will not sit in the frameForend shape and width, frame material, rebate depth

85 mm centers and 40–80 mm backset

Centers is the distance between the two axes: the center of the lever spindle and the center of the cylinder bore. On a Euro profile case it is normally 85 mm, fixed by the cylinder geometry rather than by the door, so it is rarely negotiable.

Backset is the distance from the face of the door edge, where the forend sits, to the axis of the spindle and cylinder. It varies, and this range offers six steps from 40 to 80 mm. It is the number that moves.

Measure both on the door itself, at the lock position, before the order goes out: backset from the forend face, centers from the spindle hole to the cylinder hole. On a new door, work from the supplier’s template or installation drawing.

Changing the backset does not change the cylinder length. The cylinder spans from the door face back to the case, so its length follows door thickness and the furniture on each side — the subject of AKADA’s guide to measuring a Euro profile cylinder. What a deeper backset changes is where the face hole is drilled, how far the pocket runs into the stile, and how far the lever sits from the hinge edge.

BacksetWhere the assembly sitsSuitsWatch
40 mmClosest to the edgeNarrow stiles, slim framesLeast timber around the pocket
45–50 mmThe common middle settingStandard timber single leaves, office and hotel doorsDo not assume it; templates differ
60 mmFurther inboardDeeper stiles, wide edge detailsFace hole must clear glazing beads and lock blocks
70–80 mmDeepestHeavy stiles, clearance from a wide pullLonger lever arm loads the case; stiles may run out of timber

A deeper backset is not a security upgrade: it removes more material from the stile and puts more lever arm on the follower. Choose the backset the door was prepared for.

The bore and the cam

Steel mortise lock case seated in a pocket cut into a door edge, with a satin nickel Euro profile cylinder pushed through the door face into the case and a key in the plug

The second interface is the joint itself. The case has a bore that accepts a Euro profile cylinder body and a cam slot at the centers; the cylinder’s cam nose drops into that slot and turns the deadbolt. The retaining screw passes through the case and threads into the cylinder body.

Bore, cam slot and screw hole have to line up at once. That is why a cylinder of the right length can still be the wrong part: one whose cam sits off the slot turns freely and moves nothing, and one whose threaded hole misses the case’s screw hole cannot be retained.

Test it dry before the door is closed up: cylinder in, one turn of the key, deadbolt out and back. If the key turns without moving the bolt, check the cam engagement. The cylinder is a separate purchase, and the AKADA Euro profile cylinder range with thumb turn and double cylinder options is where that half of the joint is decided.

Follower: 8 mm or 9 mm, and why the lever sags

The follower is the square hole in the case that the spindle passes through on its way from one lever to the other. It is the third interface, and the one behind the complaint buyers hear most: a lever that droops, rattles, or moves a few degrees before the latch does anything.

Both are standard, and both are offered here. They are not interchangeable, and no amount of tightening fixes a mismatch.

SpindleFollowerWhat the user feels
8 mm8 mmCorrect drive, minimal play, latch moves with the lever
8 mm9 mmPlay at the spindle: lever drops and rattles before the latch moves
9 mm8 mmSpindle will not enter; forcing it damages the follower

Sprung furniture on a sprung follower is the other trap: two springs work against each other, the lever feels heavy and the latch travels short. Buy the case and the furniture as one decision. Note the spindle size on the schedule beside the lock, confirm the length suits door thickness plus both roses, and record whether the furniture is sprung.

Forend: round head, square head and the door edge

The forend is the plate the customer sees and the fourth interface. It has to cover the pocket, sit flat on the edge, and let the door close without rubbing.

This range offers round head and square head plates, 3 mm thick, 20, 22, 23 or 24 mm wide, in stainless steel or vacuum metallized finishes. Round head plates have radiused ends and suit a rounded edge or a curved frame stop; square head plates suit a square-cut edge.

Thickness and width are fit items, not style choices. A 3 mm plate sits proud of the edge by its own thickness, so the forend face becomes the closing face of the door — which is why a pocket cut too shallow produces a door that rubs along its whole height. A plate narrower than the pocket leaves a slot visible on both sides; a wider one overhangs the stile and catches the stop.

On a rebated leaf — the meeting stile of a pair, or a door closing into a rebate — the strike has to be packed or a rebate kit used, otherwise the forend meets the rebate shoulder and the door cannot close flush.

Stainless steel (SS, PSS) suits external doors and high-traffic interiors; vacuum metallized satin brass, PVD, AB and AC suit interiors where the plate has to match the lever. Corrosion resistance is a graded property in EN 12209, so on an external door the finish is a specification item.

Function: spring latch plus a two-turn deadbolt

A spring latch plus a deadbolt that takes two turns of the key is the right default for a single-leaf door that must latch shut behind people and then be locked. The latch handles daily traffic and the self-closing action; the first turn throws the bolt, the second drives it to full throw.

It is wrong in three situations: On a public escape route the leaf needs panic hardware to EN 1125 or EN 179, a sash lock is not that product. On a tall, heavy or exposed leaf, one bolt may not hold the door flat against the frame, and the AKADA triple-bolt mortice lock spreads the load over three points. Where there is no lever at all — a store, a plant room, a riser — a plain deadlock is cheaper than a case with a follower nobody uses.

FunctionRight forWrong for
Spring latch plus two-turn deadboltSingle leaves that must latch and then lock: offices, apartments, hotel back-of-houseEscape routes needing panic hardware; very tall or exposed leaves
Triple-bolt mortice lockHeavy or tall leaves, external entrance doorsLight interior doors where extra bolts add cost, not benefit
Deadlock onlyStore rooms, doors with no lever and no daily trafficDoors that must latch shut behind people
Multipoint lockFull-height locking on entrance doors built for itRetrofits into an existing single-leaf pocket

External fire and smoke doors

An EN 12209 Grade 3 lock is not, by itself, a fire door lock, and that misunderstanding is usually discovered at inspection.

EN 12209 classifies the lock in a coded string of digits. The first digit is the category of use, and grade 3 is the high-frequency public-use grade: doors used by people with little incentive to take care. Fire and smoke suitability is a different digit, recording whether the lock is approved for fire and smoke door assemblies on the basis of tests to EN 1634-1 or EN 1634-3. Ask for the full classification code, not the headline grade.

EN 12209 classifies locks and locking plates; it does not certify a door assembly. Fire performance belongs to the complete doorset as tested, which is why the same lock can be acceptable on one tested door and not on another.

On an external fire or smoke door, verify six things and keep the answers in the project file:

  1. The doorset’s test evidence, and whether the lock is named in it for that leaf.
  2. The lock’s declaration of performance, including the fire digit for the exact article number.
  3. The strike: correct for the frame material, fully recessed, consistent with what was tested.
  4. Intumescent protection around case and strike, where the doorset’s test calls for it.
  5. A self-closer that closes and latches the leaf from any angle. A lock cannot compensate for a door that does not close.
  6. Positive latching. A fire door held only by the deadbolt, with the latch missing the keeper, is a defect whatever grade is printed on the box.

This range is listed for single-leaf doors in wood and metal, and as suitable for external fire and smoke doors. The rating period and acceptance route come from the doorset, and any figure quoted to a client should come from the certificate.

Seven steps from template to a door that closes

  1. Set out from the supplier’s template, not the old lock. Mark 85 mm centers and the backset for your article number on the door edge and the door face.
  2. Cut the pocket to the case depth, sides square and floor flat: too deep and the case rocks, too shallow and the forend stands off.
  3. Drill the face hole from both sides, meeting in the middle, so breakout does not lift the veneer.
  4. Trial-fit the case dry: forend flat without rocking, screw holes lined up, latch clear of the pocket.
  5. Fit the strike and check engagement before the final screws go in. Latch and deadbolt must enter without force; adjust the strike, not the case.
  6. Fit the cylinder and spindle: cylinder seated, retaining screw through the case and home, spindle crossing the follower and both levers at the right length.
  7. Commission the assembly: latch, two turns, lever feel, key operation. Fix anything that rubs at the strike or the door, never at the case.

Handover checks

Three-quarter view of an oak door edge ajar against a steel jamb, the stainless forend and its beveled latch and square deadbolt facing the keeper opening and deadbolt pocket of a recessed stainless strike plate

Five checks, at the frame and with the key in hand:

  • Latch engagement. The beveled tongue sits inside the keeper, held by it, with no rattle when pushed.
  • Deadbolt throw. Two full turns drive the bolt to full extension without binding, and both reverse cleanly.
  • Lever feel. No droop, no lift before the latch moves, positive return to rest on both sides.
  • Key operation. Smooth at both faces, no drag on the second turn.
  • Strike alignment. No witness marks, no gap change as the door closes.

Failure modes mapped to the four interfaces

Symptom at handoverInterfaceCheck first
Door will not close without a pushForend and strikePlate proud of the edge, strike too shallow, rebate unset
Door closes but the latch does not holdForend and strikeKeeper out of line; tongue short of the keeper
Key turns but the door is not lockedBore and cam, then strikeCam not in the slot; bolt hitting the frame instead of the pocket
Lever droops or lifts before the latch movesFollower and spindleSpindle too small for the follower, or too short
Key stiff on the second turnBore and camCylinder misaligned, or case distorted by over-tight screws
Forend shows a gap at one endForendPlate not seated in the pocket; edge not square

Common Mistakes

  • Ordering the case and assuming a cylinder is included.
  • Checking the cylinder first and the door second.
  • Fitting an 8 mm spindle into a 9 mm follower because it goes in.
  • Choosing a 24 mm forend for a narrow stile.
  • Ignoring the rebate on a pair of doors until the strike will not sit.
  • Reading EN 12209 Grade 3 as a fire rating.
  • Filing the strike or loosening the case to close a door.

FAQ

Does the lock come with a cylinder?

No. The case ships with latch, deadbolt, forend, striking plate and screws. The cylinder and keys are a separate purchase with their own specification: length for each side, key or thumb turn, security level.

Can I change the backset on an existing door?

Not practically. The backset is fixed by the pocket and face hole already in the door. A deeper one means re-cutting the pocket and drilling a new face hole; a shallower one may leave part of the old pocket exposed.

Are 8 mm and 9 mm followers interchangeable?

No. A 9 mm spindle will not enter an 8 mm follower, and an 8 mm spindle in a 9 mm follower leaves play that shows up as a drooping, rattling lever.

What does a fire door need from the lock?

A fire digit in the EN 12209 code that covers fire and smoke door assemblies, membership of the tested doorset specification, and correct installation — recessed strike, intumescent where the test calls for it, positive latching under a self-closer. Grade 3 alone answers none of those.

Bottom Line

A lock with cylinder is a case and a cylinder bought as two parts and matched on four interfaces. Check centers and backset against the door, confirm the bore and cam accept the cylinder, match the follower to the spindle, and settle the forend and strike before anything is cut. On a fire or smoke door, add the classification code and the tested doorset.

Disclosure: this guide is published by AKADA Hardware, the manufacturer of the product referenced below.

For a single-leaf timber or metal door that needs a beveled spring latch and a two-turn deadbolt, with 85 mm centers, six backset options, an 8 or 9 mm follower and a forend in four widths from 20 to 24 mm and six finishes, the specification above maps directly onto the AKADA Euro Cylinder sash lock, an EN 12209 Grade 3 case for single-leaf wood and metal doors.

    More Articles